EP-RC51 Agricultural Lawn Mower Gearbox
| ITEM | EP-RC51 Lawn Mower Gearbox |
| Ratio | 1:1.47/1:1.93 |
| Teeth | 22/15 29/15 |
| Module | 5.08 /4.0 |
| Power(HP) | 30 |
| Rated Input | 540rpm |
| Input/Output Description | Spline /Taper spline |
| Weight(N.W) | 29KG |
We supply different power Agricultural gearboxes, also we could offer OEM/ ODM service according to your drawing / sample.RG series have the features of high versatility,good combination and heavy loading capability, along with other merits such as easy to attain various transmission ratios, high efficiency.We supply different power Agricultural gearboxes, also we could offer OEM/ ODM service according to your drawing / sample.
1.We have 20 years ODM &OEM experience for gearbox
2.Goods 100% be tested before shippment
3.24 Hours for services
4.ODM & OEM: The technology Dpt. Can R&D new mould according to customer’s requirement.
5.The favorable factory price
6.Package and Brand can be Customized
Lawn Mower Gearbox Lubrication Instructions:
NOTE: These instructions apply to all Mower decks with gear-driven blades. For the mower with belt-driven blades, see Mower Deck Lubrication in this section.
Lawn Mower Gearbox (Tee Gearbox and Blade drive gearbox) connected as an integral component, Oil flows freely between them.
This type of agricultural gearbox is permanently lubricated (oil-filled) and sealed and does not require periodic lubrication.
However, the transmission oil seal should be checked every 25 hours for signs of oil spills; In particular, the lower seal of the blade drive gearbox should be checked, Because they operate in a dirty environment.
If oil leaks are found, replace the oil seals and relubricate the gearbox assembly as follows:
1. Remove the Lawn Mower Gearbox cover (foot pedal). deck direction Should be in the normal operating position.
2. Clean the area around a single Lawn Mower Gearbox Cover to prevent contamination from entering Gearbox.
3. Remove the fixing Screws for blade drive gearbox cover.
4. Check the lubricant level in the gearbox. if Insufficient lubricating oil, please add SAE EP (extremely pressure) 90W oil until the oil level reaches (submerged) Horizontal shaft in gearbox (the axis is parallel to the cover).
NOTE: If the gearbox is fully Drain the oil, about 5 fl. oz (15 cl) oil per gearbox to refill the gear drive components.
Note: Due to the gearbox
It is connected as a unit by connecting pipes, so it is necessary to add Grease slowly. Wait a few minutes after adding oil , allowing the oil to flow throughout the assembly, and Allow oil level to stabilize before reassembly.
Important: Do not overfill the Lawn Mower Gearbox. The gearbox assembly has no exhaust. Filling up the fuel can cause excessive pressure , resulting in an oil leak.
5. Check the condition of the cover gasket, Replace if worn or damaged. Reinstall the transmission cover ;Tighten the screws to 24 in-lb (2.7 N⋅m).
PTO Shafts for Agricultural Gearboxes are Available.
Agricultural equipment includes a variety of PTO shafts. Each 1 is connected by yokes at each end and rotates between 540 and 1,000 rpm. A safety shield is commonly installed on both ends of a PTO shaft to protect the operator. These protective shields are also found in tractors and agricultural implements, and they ensure maximum efficiency. Added safety is also provided by the use of internal yokes.
The agricultural PTO gearbox is designed to change the output speed of a PTO tractor drive shaft. It can be used as a decreasing or increasing ratio gearbox. With the decrease ratio gearbox, it reduces the PTO shaft’s speed from 1000 rpm to 540 rpm, allowing you to use equipment designed for 540 rpm. On the other hand, an increasing ratio gearbox increases the speed of the PTO shaft from 540 rpm to 1000 rpm.
Customized service of agricultural gearbox
Our Lawn Mower Gearbox has many items for your choice and we can produce as per your drawing or sample to meet your special request.
Other Agricultural Gearboxes
Agricultural Gearbox Production Workshop
Hangzhou Ever-power Transmission Machinery Co., Ltd. was established in 2006. The company is located in Zhejiang Hangzhou, with 90 employees, an area of 3800 meters, and an annual output value of 40 million yuan. The company is committed to the R & D, manufacturing, and personnel training of various gearboxes, reducers, and construction machinery, including spiral bevel gearbox, spur gearbox, worm gearbox, and cylindrical gearbox. It also includes a variety of high-pressure cast valve body and shell products. Its products are used in various applications, such as agricultural mowers, snow sweepers, fertilizer applicators, grain conveyors, industrial equipment, oil mining machinery, marine industrial equipment, and engineering hydraulic components. More than 95% of its products are exported to Europe, the United States, and Australia. Asia and Canada. The company has strong technology and R & D capabilities, produces reliable and high-quality products, pursues a unique business philosophy and enjoys a high reputation in the manufacturing industry. Welcome to contact us by phone or email.
